BS EN 10210 Pipes Material manufcaturer in india at low price according to Standard
BS EN 10210 Pipes Material is made up of a low carbon steel material that has 0.22% carbon, silicon, 1.6% manganese, sulfur, phosphorus and other elements in trace amounts. Multi Metals (India) is a leading EN 10210-1 Seamless Pipes Manufacturer and supplier. The pipes come in hot finished and circular hollow section. The material is deoxidized as fully killed steel.
The materials standard EN 10210-1 Pipes and Tubes come in different thicknesses and there are material grades such as the EN 10210/EN 10219 – S185, S235JR, S235J0, S355JR, S355J0 and S355J2. The size range is between 10mm*10mm to 800mm*800mm. The EN 10210-1 Carbon Steel Seamless Pipes and Tubes come in 0.5mm to 40mm wall thicknesses and lengths ranging from 6000mm to 14000mm. These mild steel products can be used in structural applications such as bridges, building, cranes, frame structures, racks, mechanical frames and in railings.
The EN 10210-1 hot-finished hollow section tube has less hardness than the high carbon steel grades. But the different procedures such as carburization can increase the surface hardness of the EN 10210-1 Grade Pipes can be increased. There are round, square, rectangular and hydraulic pipes and tubes. Please contact us for more information on the different EN 10210-1 Gr Welded Pipe types and prices.
EN 10210-1 Seamless Pipes Suppliers, Have difficulty to find EN 10210-1 Pipes and Tubes in tough sizes ? Call Multi Metals India now
| Outer diameter and wall Thickness | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Execution | Size Range | OD Tolerance | Wall tolerance | ||||||
| Hot-rolled Tube | OD – 80 mmOD > 80 mmWall < 12 mmWall - 12 mm | ± 0.4 mm± 0.5 % of OD | ± 0.7 mm± (5 % x wallthickness + 0.1 mm | ||||||
| Hot-rolled peeled tube | All sizesWall < 12 mmWall - 12 mm | + 0.25/- 0 mm | ± 0.8 mm± (5 % x wall thickness+ 0.2 mm) | ||||||
| Cold Worked tubecold-rolled or cold-drawn | OD < 40 mmOD 40 - 80 mmOD > 80 Wall Thickness< 6 mm Wall Thickness6 - 8 mm Wall Thickness > 8 | + 0.30/- 0 mm*+ 0.35/- 0 mm*+ 0.40/- 0 mm* | ± 0.30 mm± 0.35 mm± 0.40 mm | ||||||
| Component length (mm) | OD 30-100 mm | OD 100-254 mm |
| 10-100 | + 1.0/- 0 | + 2.0/- 0 |
| 100-600 | + 2.0/- 0 | + 3.0/- 0 |
| 600-1200 | + 3.0/- 0 | + 4.0/- 0 |
| 1200-5000 | + 5.0/- 0 | + 6.0/- 0 |
| Seamless Pipe Size | 4 to 219mm W. T.: 0.5 to 20mm |
|---|---|
| Standard | GB, IS, JIS, ASTM, ASME, AISI, DIN, EN Pipe |
| Welded Pipe Size | 5.0 mm – 1219.2 mm |
| Tube Swg & Bwg | 10 Swg.,16 Swg., 12 Swg., 14 Swg., 20 Swg., 18 Swg. |
| Seamless Tube Size | 3.35 mm OD To 101.6 mm OD |
| EFW Pipe size | 5.0 mm – 1219.2 mm |
| Swg & Bwg | 10 Swg., 12 Swg., 14 Swg., 16 Swg., 18 Swg., 20 Swg. |
| Pipe Schedule | SCH40, SCH40S, STD, SCH80, XS, SCH60,SCH5, SCH10, SCH10S, SCH20, SCH30, SCH80, SCH120, SCH140, SCH160, XXS |
| Welded Tube Size | 6.35 mm OD To 152 mm OD |
| Length | Single Random, Double Random, Standard & Cut length Pipe & Tube |
| wall thickness | 0.020" –0.220", (special wall thicknesses available) |
| Form | U’ bent or Hollow,Round, Hydraulic, ‘ LSAW, Straight Pipe, Boiler, Clad Pipe, Rectangular, Square Pipe Etc |
| Finish | Polished, AP (Annealed & Pickled), BA (Bright & Annealed), MF |
| Material Test Certificates (MTC) | Material Test Certificates (MTC) as per EN 10204/3.1B, EN 10204 3.1 and EN 10204 3.2, 100% Radiography Test Report, Raw Materials Certificate, Third Party Inspection Report, Fumigation Certificates, Heat Treatment Charts, EN 10210-1 Carbon Steel Pipe HS Code Commercial Invoice, Form A for Generalized System of Preferences (GSP) |
| Type | Welded, Seamless, ERW, EFW, Fabricated Pipe, ‘U’ bent or Hollow, Hydraulic, LSAW, Boiler, Straight Tube, Tube Coil, Round, Rectangular, Square Tube etc |
| End | Plain End, Beveled End, Treaded Pipe & Tube |
| Application | Oil Pipe & Tube, Gas Pipe & Tube, Fluid Pipe & Tube, Boiler Pipe & Tube, Heat exchanger Tube |
| Value Added Service | Draw & Expansion as per required Size & Length, Polish (Electro & Commercial) Annealed & Pickled Bending, Machining Etc. |
| Marking | All EN 10210-1 Grade Carbon Steel Seamless Tubes are marked as follows: Standard, Grade, OD, Thickness, Length, Heat No. (Or according to the customer’s request.) |
| Specialize in |
|
| Manufacturers of |
|
| We can also cut, thread, and groove Carbon Steel Seamless Pipe to meet your specifications. Pipe Dimension ANSI/ ASME B36.19, B36.10, B2.1 | |
Supply Cut to length EN 10210-1 hot-finished hollow section tube in all sizes and diameter as per Client requirement
Element |
Permissible maximum content in the cast analysis |
Permissible deviation of the product analysis from specified limits for the cast analysis |
C a |
≤0.20 |
﹢0.02 |
＞0.20 |
﹢0.03 |
|
Si |
≤0.60 |
﹢0.05 |
Mn |
Non-alloy ≤1.60 |
﹢0.10 |
Fine grain ≤1.70 |
﹣0.05 ﹢0.10 |
|
P |
Non-alloy ≤0.040 |
﹢0.010 |
Fine grain ≤0.035 |
﹢0.005 |
|
S |
Non-alloy ≤0.040 |
﹢0.010 |
Fine grain ≤0.030 |
﹢0.005 |
|
Nb |
≤0.060 |
﹢0.010 |
V |
≤0.20 |
﹢0.02 |
Ti |
≤0.03 |
﹢0.01 |
Cr |
≤0.30 |
﹢0.05 |
Ni |
≤0.80 |
﹢0.05 |
Mo |
≤0.10 |
﹢0.03 |
Cu |
≤0.35 |
﹢0.04 |
0.35＜Cu≤0.70 |
﹢0.07 |
|
N |
≤0.025 |
﹢0.002 |
AItotal |
≥0.020 |
﹣0.005 |
a For S235JRH in thicknesses ≤16mm, the permissible deviation=0.04%C,and for thicknesses＞16mm and ≤40mm the permissible deviation=0.05%C |
||
| Steel Grade | Chemical Composition Limits (%) | |||||
| C Max. | Si Max. | Mn Max. | P Max. | S Max. | N Max. | |
| S235JRH | 0.17 | / | 1.40 | 0.040 | 0.040 | 0.009 |
| S275J0H | 0.20 | / | 1.50 | 0.035 | 0.035 | 0.009 |
| S275J2H | 0.20 | / | 1.50 | 0.030 | 0.030 | / |
| S355J0H | 0.22 | 0.55 | 1.60 | 0.035 | 0.035 | 0.009 |
| S355J2H | 0.22 | 0.55 | 1.60 | 0.030 | 0.030 | / |
| S355K2H | 0.22 | 0.55 | 1.60 | 0.030 | 0.030 | / |
| steel Grade | Mechanical Properties | Impact Energy (KV J) | ||||
| Yield Strength (Mpa) | Tensile Strength (Mpa) | Elongation (%) | Test Temperature At Test Temperature of ℃ | |||
| -20 | 0 | 20 | ||||
| S235JRH | 235 | 360-510 | 26 | / | / | 27 |
| S275J0H | 275 | 410-560 | 23 | / | 27 | / |
| S275J2H | 275 | 410-560 | 23 | 27 | / | / |
| S355J0H | 355 | 510-680 | 22 | / | 27 | / |
| S355J2H | 355 | 510-680 | 22 | 27 | / | / |
| S355K2H | 355 | 510-680 | 22 | 40 | / | / |
| DIN | EN | BS | NFA | ASTM | ASME |
| – | EN 10210-1 | – | – | – | – |
| Wall | Sizes ( O.D.) |
|---|---|
| .010 | 1/16" , 1/8" , 3/16" |
| .020 | 1/16" , 1/8" , 3/16" , 1/4" , 5/16" , 3/8" |
| .012 | 1/8" |
| .016 | 1/8" , 3/16" |
| .028 | 1/8" , 3/16" , 1/4" , 5/16" , 3/8" , 1/2" , 3/4" , 1" , 1 1/2" , 2" |
| .035 | 1/8" , 3/16" , 1/4" , 5/16" , 3/8" , 7/16" , 1/2" , 16" , 5/8" , 3/4" , 7/8" , 1" , 1 1/4" , 1 1/2" , 1 5/8" , 2" , 2 1/4" |
| .049 | 3/16" , 1/4" , 5/16" , 3/8" , 1/2" , 16" , 5/8" , 3/4" , 7/8" , 1" , 1 1/8" , 1 1/4" , 1 1/2" , 1 5/8" , 2" , 2 1/4" |
| .065 | 1/4" , 5/16" , 3/8" , 1/2" , 16" , 5/8" , 3/4" , 7/8" , 1" , 1 1/4" , 1 1/2" , 1 5/8" , 1 3/4" , 2" , 2 1/2" , 3" |
| .083 | 1/4" , 3/8" , 1/2" , 5/8" , 3/4" , 7/8" , 1" , 1 1/4" , 1 1/2" , 1 5/8" , 1 7/8" , 2" , 2 1/2" ,3" |
| .095 | 1/2" , 5/8" , 1" , 1 1/4" , 1 1/2" , 2" |
| .109 | 1/2" , 3/4" , 1" , 1 1/4" , 1 1/2" , 2" |
| .120 | 1/2" , 5/8" , 3/4" , 7/8" , 1" , 1 1/4" , 1 1/2" , 2" , 2 1/4" , 2 1/2" , 3" |
| .125 | 3/4" , 1" , 1 1/4" , 1 1/2" , 2" , 3" , 3 1/4" |
| .134 | 1" |
| .250 | 3" |
| .375 | 3 1/2" |
We Guarantee Fastest Delivery of EN 10210-1 Gr Welded Pipe with All Documents Including Mill Certificate
|
|
are you looking for en 10210-1 coating Pipe Specification, Composition, Wall Thickness and Weight Chart
| 1/8" IPS(.405" O.D.) | 3 1/2" IPS( 4.000" O.D.) |
|---|---|
| SCH 40, 80 | SCH 10, 40, 80, 160, XXH |
| 1/4" IPS(.540" O.D.) | 4" IPS(4.500" O.D.) |
| SCH 10, 40, 80 | SCH 10, 40, 80, 160, XXH |
| 3/8" IPS(.675" O.D.) | 5" IPS( 5.563" O.D.) |
| SCH 10, 40, 80 | SCH 10, 40, 80, 160, XXH |
| 1/2" IPS(.840" O.D.) | 6" IPS(6.625" O.D.) |
| SCH 5, 10, 40, 80, 160, XXH | SCH 5, 10, 40, 80, 120, 160, XXH |
| 3/4" IPS(1.050" O.D.) | 8 ” IPS(8.625" O.D.) |
| SCH 10, 40, 80, 160, XXH | SCH 5, 10, 40, 80, 120, 160, XXH |
| 1" IPS:(1.315′ O.D.) | 10" IPS(10.750" O.D.) |
| SCH 5, 10, 40, 80, 160, XXH | SCH 10, 20, 40, 80 (.500), TRUE 80(.500) |
| 1-1/4" IPS(1.660" O.D.) | 12" IPS(12.750" O.D.) |
| SCH 10, 40, 80, 160, XXH | SCH 10, 20, 40(.375), TRUE40(.406), SCH80(.500) |
| 1-1/2" IPS(1.900" O.D.) | 14" IPS(14.000" O.D.) |
| SCH 10, 40, 80, 160, XXH | SCH10 (.188), SCH40 (.375) |
| 2" IPS(2.375" O.D.) | 16" IPS(16.000" O.D.) |
| SCH 10, 40, 80, 160, XXH | SCH10(.188), SCH40(.375) |
| 2 1/2" IPS(2.875" O.D.) | 18" IPS (18.000" O.D.) |
| SCH 10, 40, 80, 160, XXH | SCH-40 (.375) |
| 3" IPS( 3.500" O.D.) | |
| SCH 5, 10, 40, 80, 160, XXH |
- Structural hollow section manufacturing process:
Structural hollow sections are manufactured by seamless or by welding.
Welded sections manufactured by continuous process.
Electric welded hollow sections are supplied without trimming the internal weld bead. - Delivery condition:
Qualities JR, J0, J2 and K2 - Hot finished
Qualities N and NL - normalized. (normalized rolled)
- for accelerated cooling +DC
- for quenching and tempering +QT - Surface condition:
The hollow sections have a smooth surface corresponding to the manufacturing method used; bumps, cavities or shallow longitudinal grooves resulting from the manufacturing process are permissible, provided the thickness is within tolerance.